A Brief Guide to Root Protection Areas and Development

Tree Roots

Tree roots extend radially in every direction to a distance equal to at least the height of the tree (assuming no physical barriers) and grow predominantly near the soil surface.
Typically, 90% of all roots, and virtually all the large structural supporting roots, are in the upper 60cm of the soil.

What is a Root Protection Area?

The optimal rooting area for a tree, is an area defined by its height. The root protection area for a tree is the minimum area required to meet the everyday needs of a normal healthy tree.

How Big is the Root Protection Area?

The standard root protection area of a tree is described as a circle (with the tree at the centre) with a radius of 12 times the stem diameter, measured at 1.50m above ground level. The maximum radius for a root protection area (excluding ancient and veteran trees) is capped at 15.0m.

Guidance on Root Protection Areas

British Standard 5837:2012 Trees in relation to design, demolition and construction – Recommendations (BS:5837), provides ‘recommendations and guidance for arboriculturists, architects, builders, engineers, landscape architects ….. and all others interested in harmony between trees and development in its broadest sense’.
BS:5837 gives ‘recommendations and guidance on the relationship between trees and design, demolition and construction processes’, and it ‘it sets out the principles and procedures to be applied to achieve a harmonious and sustainable relationship between trees and structures
BS:5837 recommends that there should no excavation, no changes of soil level (either increases or decreases) and no compaction within the root protection area.

Ancient and Veteran Trees

It is recommended that no construction, including the installation of new hard surfacing, occurs within the root protection area of an ancient or veteran tree.
The radius of the root protection area for ancient and veteran trees, based on the current Standing Advice, is 15 x stem diameter (measured at 1.50m above ground level) or 5.0m beyond the edge of the canopy, whichever is the greater.

Proximity of Structures to Trees

The default position should be that structures are located outside the root protection area of trees to be retained. However, where there is an overriding justification for construction within the root protection area, technical solutions might be available that prevent damage to the tree(s). If operations within the root protection area are proposed, the project arboriculturist should:

a) demonstrate that the tree(s) can remain viable and that the area lost to encroachment can be compensated for elsewhere, contiguous with its root protection area, and
b) propose a series of mitigation measures.

Special Engineering for Foundations within the Root Protection Area

Where a slab for a minor structure (e.g. shed base) is to be formed within the root protection area, it should bear on existing ground level, and should not exceed an area greater than 20% of the existing unsurfaced ground.
Slabs for larger structures (e.g. dwellings) should be constructed with a ventilated air space between the underside of the slab and the existing soil surface (to enable gas exchange and venting through the soil surface). In such cases, a specialist irrigation system should also be employed (e.g. roof run-off redirected under the slab).

Temporary Ground Protection within the Root Protection Area

a) for pedestrian movements only, a single thickness of scaffold boards placed either on top of a driven scaffold frame, so as to form a suspended walkway, or on top of a compression-resistant layer (e.g. 100 mm depth of woodchip or sharp sand), laid onto a geotextile membrane;
b) for pedestrian-operated plant up to a gross weight of 2 t, proprietary, inter-linked ground protection boards placed on top of a compression-resistant layer (e.g. 150 mm depth of woodchip or 150mm of sharp sand), laid onto a geotextile membrane;
c) for wheeled or tracked construction traffic exceeding 2 t gross weight, an alternative system (e.g. proprietary systems or pre-cast reinforced concrete slabs)
to an engineering specification designed in conjunction with arboricultural advice, to accommodate the likely loading to which it will be subjected.

Permanent Hard Surfacing within the Root Protection Area

The design should not require excavation into the soil, including the lowering of levels and/or scraping, other than the removal, using hand tools, of any turf layer or other surface vegetation.

3D Cellular Confinement System

The structure of the new hard surface should be designed to avoid localized compaction by evenly distributing the loading over the track width and wheelbase of any vehicles expected to use the access.
If the new surface is likely to be subject to de-icing salt application, an impermeable barrier should be incorporated to prevent contamination of the rooting area. Run-off should be directed away from the root protection area.
Where a permeable surface is to be used by vehicular traffic, a geotextile
should be used at the base of construction to help prevent pollution contamination of the rooting area below.

Geo Textile Membrane

Permeable hard surfacing can result in soil volume moisture content remaining at or near field capacity for long periods. Where there is a risk of waterlogging, the design should incorporate appropriate land drainage.
The hard surface should be resistant to or tolerant of deformation by tree roots and should be set back from the stem of the tree and its above-ground root buttressing by a minimum of 500 mm to allow for growth and movement.